Vehicles
56 not categorized PORSCHE 930 MOUNT PLATECan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.DASRB2NS Das sport bolt-in roll bar Porsche 996/997 (w/o sunroof) 99+ General Fitment911 1998-05
$2,018.25
Make a selection ER911MNT If you need more front camber adjustment range, these elephant racing offset camberplates are for you. the monoball and mounting holes are offset, allowing up to 3/4 degree of additional camber adjustment range. just the ticket for your race car. These plates use the same spherical bearing technology as our front monoball cartridges and replace the entire factor camberplate. For even more negative camber, combine with our de-cambered ball joints. Combine with polybronze control arm bearings to achieve a rigid front suspension geometry that maintains alignment under hard braking and cornering loads. General Fitment914 1970-76
$499.00
Make a selection FVD34310016L FVD aluminium monoball relacement camber plates are designed to replace the original upper strut plates on both OEM and cup struts. FVD camber plates are manufactured using the highest quality materials and offer a wider range of camber possibilites than the OEM mount by offsetting the upper strut position. General Fitment911 TURBO/GT2 2007-09911 2009-12 911 2005-08
$494.68
Make a selection FVD34310004 The FVD front camber plate replaces the original rubber top strut mount bushings. We manufacture each camber plate in Germany and machine each from a solid block of billet aluminum. Each is fitted with a spherical bearing which allows a wide range of camber possibilities, up to 4 degrees' negative camber is possible. Sold individually. Please note: this camber plate only works in conjunction with a coil over (double spring) suspension. General Fitment911 1994-98
From $398.28
Make a selection FVD3439642PSS9 The FVD camber plate kit replaces the front and rear original rubber top strut mount bushings. We manufacture each camber plate and mount in Germany and machine each from a solid block of billet aluminum. Each is fitted with spherical bearings which allows a wide range of camber possibilities. This kit contains: 2 front camber plates 2 rear camber plates please note: this kit only works in conjunction with a pss9 / pss10 coil over (double spring) suspension in front and rear. General Fitment911 1989-94
From $1,204.50
Make a selection CPO020RR Ksport version rr damper system is built specifically for road racing only. Aggressive rates and valving are chosen for maximum handling and performance with acute reaction and responsiveness. Integrated with 36 levels of dampening adjustment, simultaneous compression and rebound adjustment, lightweight aluminum mounts, and pillow ball upper mounts on some applications. (race use only.) General FitmentBOXSTER 1997-04
$2,732.40
Make a selection M500052 Moton club sport damper system Porsche Boxster incl s 97+ General FitmentBOXSTER 1997-04
$7,761.15
Make a selection FVD343996TPSS9 Only for vehicles equipped with bilstein suspension pss9/10. General Fitment911 TURBO/GT2 2001-05911 1998-05
$1,886.38
Make a selection FVD505123964RS Rear bumper center section race look for Porsche 964/965 turbo General Fitment911 1989-94
From $399.00
Make a selection FVD512964008RSK Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon rear bumper that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 4 kg (8.81 lbs) - kevlar / carbon - mounting is just like factory, no modifications are necessary. - fits all 964 narrow body models - left and right side exits for exhaust please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. If you do not have the rs license plate light please also order 91163162004 General Fitment911 1989-94
From $1,791.90
Make a selection FVDBSK351993002 Make your next service a breeze with our pre-packaged service kits. Quality means everything to us, so we only source these parts directly in Germany. This kit contains: 1 qty. Front right rotor (zimmermann formula z) 1 qty. Front left rotor (zimmermann formula z) 1 qty. Oem set of front pads (4 total) 2 qty. Oem brake warning sensors 4 qty. Oem brake pad damping plates (for 44 mm piston) 4 qty. Oem brake pad damping plates (for 36 mm piston) 2 qty. Oem brake caliper mounting bolts - m12x72mm sold as a kit. 1 necessary per car.
$936.10
Make a selection FVDBSK351997006 Brake service kit contains: - brake discs - brake pads - caliper screws - warning contacts - damping plates - mounting parts everything you need to service your front brake complete.
$504.90
Make a selection HEI964001002S Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: includes mounting plates that must be welded in. Chromoly steel 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Tig welded. Retains full seat adjustability. Semi-gloss black finish. Cost effective for club sport use. We r...(choose a part on the right to read more)
$694.10
Make a selection HEI964001001A Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: includes mounting plates that must be welded in. Aluminum 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Retains full seat adjustability. Aluminum finish. Please note: these bars are hand made to order. They typically ta...(choose a part on the right to read more) General Fitment911 1989-94
From $830.09
Make a selection I203 Radio and heater control block off plates - until now, removing the center console from your 964/993 was not possible due to the required switches that were mounted in it. Rennline's new radio and heater control block off plates solve that problem. These plates have been specially designed to accept the factory switches installed in the center console of all 964/993 cars. Don't have the factory switches? No problem. These plates are also available without switch cutouts so you can install your own switches or gauges. Made from powder coated metal and installs in minutes on cars with the radio or heater controls removed. General Fitment911 1989-94911 1994-98
$50.00
Make a selection I206 Radio and heater control block off plates - until now, removing the center console from your 964/993 was not possible due to the required switches that were mounted in it. Rennline's new radio and heater control block off plates solve that problem. These plates have been specially designed to accept the factory switches installed in the center console of all 964/993 cars. Don't have the factory switches? No problem. These plates are also available without switch cutouts so you can install your own switches or gauges. Made from powder coated metal and installs in minutes on cars with the radio or heater controls removed. General Fitment911 1989-94911 1994-98
$50.00
Make a selection BES99105060S - + 12 crank hp & + 12 crank torque - 2 3/4 tubing (70mm) straight through design for max. Power - weighs 18 lbs. (8.5 kg), which is a 3 lbs. Savings off of OEM center muffler. - replaces stock side mufflers and stock center muffler. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 2 x 3.5 (90mm) round tips. - includes all necessary clamps and mounting brackets. - made in Germany. - intoxicating cup car growl at idle, partial throttle and wide open throttle. - no dme programming necessary, does not alter emissions, 50 state legal in the u.s. Our 991 GT3 center muffler replacements are vastly different than the baffle plated mufflers stuffed with packing that are common in the after...(choose a part on the right to read more)
$2,337.50
Make a selection JWST914PVT Durable, adjustable replacement for the rear trunk pivot. Bolt-in replacement does not require welding to install. Back-up plate reinforces the mounting area. The original pivot mount must be drilled or ground away and four new holes drilled for installation. Strong, smooth pivot will not bind or gall as can occur with the original design can be used with original torsion bars or aftermarket gas shocks. General Fitment914 1970-76
$59.50
Make a selection M500012 Moton club sport damper system Porsche 964 89-93 General Fitment911 1989-94
$7,356.15
Make a selection M500033 The 3-way adjustable moton damper features 15 positions of high speed bump, 6 positions low speed bump and 15 positions of rebound adjustment. The low speed bump adjuster is located on top of the high speed bump adjuster and can be adjusted in dependably. The low speed bump adjuster is very effective in helping to control body roll while adding to turn in and is effective in controlling pitch and squat. The 3-way adjustable moton damper is using, like the double adjustable damper, a unique blow off valve system in the canister to totally control curb stones and bumpy track conditions. General Fitment911 1998-05
$13,431.15
Make a selection M500021 The 4-way adjustable motorsport damper has been developed over the last few years in conjunction with many professional racing teams all over the world. After winning the fia European touring car championship (etcc in 2004 with our triple adjustable damper, we designed and developed this unique 4-way damper with andy priaulx's team in preparation of the 2005 fia world touring car championship (wtcc. The rest is history and the 2005, 2006 and 2007 fia wtcc title was clinched by andy priaulx running the moton 4-way damper system. General Fitment911 1984-86911 GT3 2007-11
$13,161.15
Make a selection HEI993001001S Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: incl. Mounting parts chromoly steel 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Tig welded. Retains full seat adjustability. Semi-gloss black finish. Cost effective for club sport use. We recommend adding the harness ...(choose a part on the right to read more) General Fitment911 1994-98
From $580.80
Make a selection M500071 The 3-way adjustable moton damper features 15 positions of high speed bump, 6 positions low speed bump and 15 positions of rebound adjustment. The low speed bump adjuster is located on top of the high speed bump adjuster and can be adjusted in dependably. The low speed bump adjuster is very effective in helping to control body roll while adding to turn in and is effective in controlling pitch and squat. The 3-way adjustable moton damper is using, like the double adjustable damper, a unique blow off valve system in the canister to totally control curb stones and bumpy track conditions. General Fitment911 1994-98
$12,486.15
Make a selection M500065 Moton club sport damper system Porsche 944 turbo 85-94 General Fitment944 1985-88
$7,356.15
Make a selection M500128 The 3-way adjustable moton damper features 15 positions of high speed bump, 6 positions low speed bump and 15 positions of rebound adjustment. The low speed bump adjuster is located on top of the high speed bump adjuster and can be adjusted in dependably. The low speed bump adjuster is very effective in helping to control body roll while adding to turn in and is effective in controlling pitch and squat. The 3-way adjustable moton damper is using, like the double adjustable damper, a unique blow off valve system in the canister to totally control curb stones and bumpy track conditions. General Fitment911 2009-12
$14,376.15
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |